Trusted Home Services in Dodge Center, MN

Responded to service call for bathroom exhaust fan repeatedly tripping circuit breaker during customer's installation attempt. Diagnostic inspection revealed pinched and broken wiring in ceiling cavity. Repaired issue by replacing damaged section with new wire and installed proper switch leg connection to restore safe operation of the bathroom fan.

Responded to callback for furnace failure after previous service on 2/17. Upon inspection, identified clogged condensate trap as the root cause of system shutdown. Successfully cleared the obstruction in the trap, restoring proper condensate drainage and returning the furnace to normal operation.

Successfully removed existing Moen kitchen faucet and installed customer-supplied replacement Moen model with side sprayer. Completed all necessary connections and performed functionality test with positive results - all components operating properly with no leaks observed.

Performed scheduled preventative maintenance agreement service on residential HVAC system. Accessed and inspected furnace components, completed standard tune-up procedures including filter replacement. No issues identified during service; system operating normally upon completion.

Performed scheduled preventative maintenance agreement service on air handler. Arrived within scheduled window (8-12). Conducted comprehensive system tune-up with no issues identified. Inspected and documented plumbing components including PVC pipes with proper cement application and flexible supply lines with brass fittings. System operating within normal parameters after service.

Responded to zone heating issue where basement register was drawing excessive heat from addition vent. Diagnosed airflow imbalance between zones with thermostat reading 74°F despite 68°F setpoint. Recommended closing basement vent or installing booster fan to correct distribution problem. Replaced air filter with new pleated filter during service.

Responded to no heat complaint for LP furnace over 10 years old. Diagnosed tripped rollout switch due to excessive debris on burners. Service included removing burner assembly, performing thorough cleaning to restore proper flame pattern and combustion, then verifying safe operation after reassembly.

Performed scheduled generator maintenance inspection with arrival between 8-12. Documented equipment information including POWERZONE control panel functionality and air filtration system. Provided information to management for maintenance kit quote preparation as required for service agreement completion.

Responded to service call for leaking Moen kitchen faucet. Upon inspection, determined that manufacturer had sent incorrect replacement parts. Advised customer to contact Moen for correct components and schedule follow-up appointment for faucet installation once new parts are delivered.

Responded to service call for geothermal unit with intermittent compressor operation and water leak. Diagnostic inspection revealed system shutting down after brief operation. Heat currently being provided by backup furnace. Inspected HBX ECO-0550 Control Processing Unit and internal electrical components, and noted need for temperature/pressure gauge replacement.

Performed scheduled one-time furnace tune-up on residential HVAC system. Conducted comprehensive inspection of internal components including control board, wiring connections, and drainage system. All systems verified to be in proper working order with no issues identified.

Responded to a service call regarding water dripping in basement from unknown source. Upon inspection, identified dishwasher leaking internally with water penetrating through floor into basement. Shut off water supply to dishwasher to prevent further damage. Documented existing plumbing infrastructure with photos showing copper and PVC piping configuration in the affected area.

Responded to callback for high-pitch noise during furnace startup. Inspected Lennox furnace system in basement; noise could not be fully replicated during visit. Identified loose upstairs zone damper motor that had detached from damper shaft and secured it properly to resolve the issue.

Responded to no-heat service call for aging furnace (10+ years). Diagnosed E311 error code indicating heat limits due to restricted airflow. Performed cleaning of secondary heat exchanger and removed heavily contaminated filter that was causing airflow restriction. System restored to proper operating condition.

Responded to a no-heat call for an older gas furnace unit installed in basement. Diagnostic testing revealed debris obstructing the pressure switch port, preventing proper operation. Successfully cleared blockage, restoring normal heating function and confirming proper system startup.

Responded to customer report of kitchen drain leak. Inspection revealed stainless steel goose neck drain under garbage disposal had developed a hole causing the leak. Removed damaged drain assembly and installed new 1 1/2" PVC drain assembly, resolving the issue.

Performed scheduled preventive maintenance agreement service on HVAC system. Completed comprehensive tune-up with no issues identified. System components, including drainage and ventilation piping, were inspected and verified to be functioning properly.

Responded to no-heat call for aging system (10+ years). Diagnosed failing draft inducer motor as evidenced by inspection of blower assembly. Installed new draft inducer per approved bid, verified proper operation of the system, and restored heating functionality.

Performed routine maintenance tune-up on Lennox furnace system as per prepaid service agreement. Inspected ventilation system including PVC exhaust/intake pipes and verified all connections were secure. Unit was fully operational with no issues detected upon completion of service.

Responded to no heat service call on geothermal system. Diagnostic testing revealed refrigerant undercharge. Performed initial assessment of refrigerant levels and connections. Scheduled follow-up visit for leak detection and complete repair.

Responded to no heat complaint and found severely clogged heat exchanger with significant corrosion and deterioration. Inspection revealed extensive rust on multiple components including metal brackets and internal connections. Replacement of unit recommended due to safety concerns and irreparable damage.

Responded to no-heat call for furnace less than 10 years old. Diagnostic testing revealed faulty gas valve preventing proper heating operation. Removed defective component and installed new Resideo gas valve, properly connecting all control wiring. System tested after repair and confirmed proper ignition and heat production.

Responded to a no-heat call for an aging furnace (10+ years) with improper exhaust ventilation. Diagnosed recirculating exhaust gases at the exterior termination point. Modified and replaced the existing PVC vent termination to correct ventilation issues and restore proper furnace operation.

Responded to service call for non-operational Reznor hanging furnace in metal building/garage. Diagnosed faulty gas valve as root cause of heating failure. Provided customer with repair estimate and scheduled preventative maintenance visit for potential unit replacement.

Responded to callback service for heating system not maintaining temperature above 60°F after previous transformer replacement. Diagnostic testing revealed failed blower motor in Amana furnace. Removed defective component and installed new motor to restore proper system operation and heating capability.