Your Trusted Home Services Team in Rochester, MN

Provided estimates for installation of four recessed can lights in kitchen and replacement of two bathroom exhaust fans. Assessed existing electrical circuits and ceiling access requirements to determine scope of work and material specifications for the requested lighting and ventilation upgrades.

Installed three new electrical outlets at residential property to accommodate appliance requirements. Converted hardwired dishwasher connection to receptacle outlet under kitchen sink for improved serviceability. Added dedicated 120V outlet in basement area mounted on existing plumbing infrastructure for freezer operation. Installed additional outlet in garage on exposed wall framing for general use. All installations completed per National Electrical Code requirements with appropriate wire sizing, proper grounding, and secure mounting of outlet boxes and cover plates.

Responded to water line leak originating from shower valve in upstairs bathroom. Previous visit was unable to access leak due to mold obstruction; upon return, mold had been remediated providing clear access to plumbing system. Investigation revealed leak coming from one of two back-to-back shower valves with limited access to water lines through ceiling cavity. Accessed leak location through ceiling opening, exposing copper supply lines running through floor joists. Identified corroded copper piping with visible green patina at valve connection point as source of active leak. Documented existing conditions including water damage, compromised drywall, and plumbing configuration. Assessed repair options given challenging access constraints with back-to-back shower installations and lack of direct wall access to water lines. Provided recommendations for permanent repair solutions including potential rerouting of supply lines or creation of access panel for future serviceability.

Responded to no heat/no cool condition at property. Upon inspection, discovered loose R wire at thermostat terminal causing loss of power to HVAC system. Reattached wire securely to proper terminal and verified system operation restored for both heating and cooling functions.

Responded to service call for electrical work required for home inspection. Upgraded standard outlets to GFCI receptacles to meet current safety code requirements. Addressed grounding issues on multiple outlets that were not properly grounded. Provided estimate for additional work including installation of dedicated circuit as requested. Completed GFCI installation and tested functionality of protective devices to ensure proper operation.

Responded to no hot water complaint at residential property. Upon arrival, diagnosed that the pilot light on the tanked water heater had extinguished, resulting in complete loss of hot water to the home. Successfully relit the pilot light and verified proper flame ignition and burner operation, restoring hot water service to the residence.

Responded to no cooling call on attic air handler system. Upon arrival, discovered the equipment power switch had been turned off. Restored power to unit by turning switch to on position, resolving the no cool condition.

Responded to a recall for a recently installed showerhead reported as non-functioning. Upon arrival and inspection of the chrome handheld shower unit with flexible hose and dual shower configuration, tested all fixtures and confirmed proper operation with no issues found.

Provided estimate for bathroom shower fixture replacement including installation of customer-provided trim kit, handle, tub spout, and shower head. Assessment included replacing existing faucet with new valve assembly and extending water spout to accommodate updated fixture configuration. Documentation photos captured existing conditions showing tub-to-wall interface with visible staining and in-progress valve installation through wall penetration.

Responded to service call for light fixture replacement and outlet inspection. Upon arrival, assessed existing electrical outlets and discussed additional outlet installation requirements. Accessed attic space to fish new electrical wire from existing outlet location down wall cavity to new outlet position on same wall. Prepared and presented estimate for proposed electrical work to add outlets throughout residence.

Responded to warranty call for newly installed zoned HVAC system with non-functional zone controls and humidifier. Upon arrival, diagnosed faulty zone control board preventing proper damper operation between upstairs and downstairs zones. Additionally found Aprilaire humidifier system incompletely installed with missing electrical connections. Replaced defective zone board and completed wiring of humidifier to restore full system functionality. All zones now operating correctly with proper damper control, and humidification system fully integrated and operational.

Completed installation of 50-gallon water heater, replaced bathroom faucets, and installed new shower trim fixtures including chrome shower valve and tub spout to address multiple plumbing issues. All fixtures were properly mounted, tested for leaks, and confirmed to be in full working order upon completion.

Performed comprehensive one-time air handler tune-up and maintenance service. Completed full system inspection of internal components including blower motor assembly, electrical control board, and all associated wiring connections. Installed new filter and verified proper operation of all mechanical and electrical systems.

Completed follow-up service call to address attic air handler condensate drainage issue that could not be resolved during previous visit due to insufficient pitch. Successfully installed new drain line with proper slope to ensure adequate gravity drainage. Routed condensate line from attic unit through interior space and terminated at exterior wall of residence. Performed leak test by introducing water into drain pan and verified complete drainage with no leaks at connections or along pipe run. System now draining properly with appropriate pitch maintained throughout drain line installation.

Performed on-site evaluation for electric vehicle charger installation requiring electrical service upgrade from 150 to 200 amps. Assessed existing electrical panel located in basement, which shares a common wall with the garage, providing ideal conditions for straightforward wire routing. Provided comprehensive estimate for 40-amp EV charger installation with multiple mounting location options in the garage to accommodate customer preferences and optimal charging accessibility.

Completed comprehensive electrical inspection for property. Identified multiple locations requiring GFCI protection upgrades to meet current safety code requirements. Documented existing electrical outlets and switch configurations, provided detailed estimates for necessary GFCI installations, and completed full inspection report.

Completed comprehensive HVAC maintenance service on both heating and cooling systems as part of a BOGO furnace and air conditioning special. Performed full maintenance inspection and servicing on the Maytag furnace unit and Carrier outdoor condensing unit, verifying proper operation of all components, electrical connections, and system efficiency. All equipment found to be functioning within normal parameters with no immediate repairs required.

Installed seven recessed wafer lights in unfinished basement with exposed ceiling joists. Rerouted existing electrical wiring from under floor joists to run properly between joists to allow for future ceiling installation. Provided estimate for adding dedicated outlet under kitchen sink for garbage disposal.

Responded to customer complaint of high humidity levels in home. Upon inspection, found HRV system was drawing in outdoor humidity due to incorrect dehumidistat settings. Adjusted Healthy Climate HRV ventilation system dehumidistat control to proper settings and instructed customer on correct operation to prevent recurrence.

Performed maintenance cleaning on wall-mounted mini split system that had accumulated significant dirt and debris. Thoroughly cleaned the indoor air handler unit, removed buildup from components, and vacuumed the condensate drain line to ensure proper drainage and system efficiency.