Your Trusted Home Services Team in Rochester, MN

Installed dedicated electrical circuit for newly installed jet tub, running wiring from main breaker panel through bathroom, under stair storage area, and back up into bathroom to supply new outlet. Completed circuit installation and outlet mounting to provide proper power supply for jet tub operation.

Responded to callback for refrigerant leak repair on R410A system. Diagnosed failed service valves requiring replacement with 7/8" brass service valves (part #102831-05). Ordered necessary components and advised customer that lineset replacement may also be required depending on leak location assessment during valve installation.

Provided on-site estimate for installation of 19kW EV charger requiring upgraded electrical service. Assessment determined need for Class 320 (400A) meter split to accommodate two separate 200A panels. Proposed installation plan includes running electrical wire from basement panel through unfinished utility room into garage, with conduit routing to customer's preferred charging location between garage stalls. Documented existing electrical panel configuration and available space for additional distribution equipment necessary to support 80-amp EV charging circuit.

Performed maintenance flush on 40-gallon atmospheric water heater to remove sediment buildup and ensure optimal performance. Additionally, addressed two loose faucet fixtures: tightened bathroom sink faucet and secured hot water faucet on second sink to prevent further deterioration and potential leaks.

Responded to service call and successfully removed and replaced a failed ECM blower motor per sold estimate. The old motor was extracted from the HVAC system, and a new ECM motor and module were installed to restore proper system operation and airflow.

Responded to service call for heat pump with disconnected outdoor temperature sensor found on ground next to unit. Upon inspection, determined sensor had detached from its mounting location on exterior wall. Reinstalled sensor to proper position on building exterior adjacent to heat pump unit, secured mounting, and verified wire connection integrity. System restored to normal operation with sensor properly positioned for accurate temperature monitoring.

Responded to emergency call for reported water leak originating from either shower drain or refrigerator supply line. Upon arrival, temporarily shut off main water supply to house to stop active leaking. Conducted thorough inspection of plumbing fixtures, accessed ceiling cavity to examine pipes and potential leak sources. Unable to locate active leak during inspection period. Restored water service to residence and advised property occupant to monitor situation and note which fixtures are in use if leaking recurs to help isolate source.

Responded to no heat call on 5-year-old furnace displaying error code. Diagnosed failed control board relay preventing system operation. Ordered replacement control board for installation, as unit is outside warranty coverage.

Responded to service call for inoperative dryer circuit. Upon inspection, discovered blown fuse at disconnect box located above dryer unit, which was protected by both a 30-amp circuit breaker at main panel and fused disconnect. Bypassed the faulty fused disconnect and established direct wiring connection from the 30-amp breaker to the dryer, restoring power to the appliance.

Responded to service call for refrigerator repeatedly tripping circuit breaker. Diagnosed issue as loose electrical connection at the circuit breaker panel. Tightened the affected connection, verified secure termination, and performed full panel inspection to ensure all connections were properly secured and no additional issues were present.

Responded to a leaking toilet with water seeping from the base. Upon inspection, identified a failed wax foam ring as the primary cause of the leak, along with a cracked flush valve requiring replacement. Ordered the necessary flush valve component and will return to complete the rebuild, install the new flush valve, and replace the wax ring to restore proper seal and function.

Performed inspection of hard-wired smoke alarm system and identified that one smoke detector was wired independently and not interconnected with the remaining detectors in the system. Confirmed operational status of individual units and documented ceiling-mounted smoke detector locations throughout the property.

Responded to no heat call and discovered water accumulation in furnace blower assembly and inducer motor due to improperly installed condensate drain line. Found drain line routing error causing secondary drain pan to overflow and allowing carbon monoxide to leak through apartment drain system. Unit was immediately shut down and red-tagged for safety due to CO hazard and water damage to critical components. Provided estimate for corrective repairs including proper drain line installation and component assessment.

Responded to emergency call for burst pipe and water leak on half-inch copper line located near the water meter inside the residence. Successfully repaired the leak on the supply line using appropriate plumbing techniques and verified system integrity. All plumbing fixtures, valves, and pressure tank connections were inspected to ensure proper operation following the repair.

Responded to reported water leak from either water heater or water softener system. Upon thorough inspection of both the water heater and water treatment system, including all visible copper piping, PVC connections, and equipment components, no active leaks were detected. Both water heater and water softener were operational and functioning properly at time of service. Advised customer to monitor system during usage and contact for follow-up visit if leak reoccurs.

Responded to service call for bathroom exhaust fan evaluation. Upon inspection, assessed existing fan unit and housing condition. Provided estimate for complete bathroom exhaust fan housing replacement due to deteriorated condition of existing assembly. Documented electrical junction box configuration and verified circuit breaker panel connections for future installation work.

Responded to no hot water complaint and diagnosed low water pressure issue on IBC wall-mounted boiler system. Adjusted and increased system water pressure to restore proper operation of the hydronic heating unit. Verified hot water restoration and confirmed all valves, pressure gauges, and copper piping connections functioning correctly after pressure adjustment.

Responded to a leaky pipe emergency and located a pin hole leak in the 1/2" copper supply line coming from the water softener. Cut out the damaged section of copper piping and installed new copper pipe with proper fittings. Tested the system upon completion and verified all connections were secure with no leaks present and proper water flow restored.

Replaced defective J-trap PVC assembly under white double-basin kitchen sink and installed new drain assemblies for both basins. All plumbing connections were secured and tested for proper drainage, with white PVC piping configured to accommodate the dual-basin setup with black drain fittings.

Responded to service call for leaking faucet and floor drain closure request. Upon arrival, assessed bathroom sink with chrome dual-handle faucet installation and inspected the leaking condition. Provided detailed estimate for new kitchen faucet installation and pop up assembly replacement to address the plumbing concerns.