Your Trusted Home Services Team in Rochester, MN

Performed comprehensive furnace tune-up and seasonal maintenance inspection. Verified proper gas combustion with blue flame pattern, inspected burner assembly and heat exchanger, tested all safety controls, and confirmed system operation within manufacturer specifications. Unit found in good working condition with no deficiencies noted.

Completed comprehensive tune-up on aging furnace system. Performed thorough inspection of all components including heat exchanger, blower motor assembly, gas connections, and venting system. Unit is operating within normal parameters with no safety concerns identified at this time.

Completed comprehensive duct cleaning and dryer vent service after identifying dust accumulation in the ventilation system and lint buildup in the dryer vent. Thoroughly cleaned all accessible ductwork and dryer ventilation components, removing debris and restoring proper airflow throughout the system.

Replaced existing 50-gallon atmospheric natural gas water heater with new Bradford White unit. Completed full installation including water and gas line connections, proper venting, and verification of all safety controls and operational functionality.

Responded to callback on newly installed AC system experiencing repeated breaker trips and non-functioning condenser fan. Diagnosed compressor drawing excessive amperage during startup cycles, causing electrical overload. Installed hard start capacitor kit to reduce inrush current and facilitate proper compressor operation, resolving breaker trip issue and restoring full system functionality.

Responded to callback for water line leak that had been previously addressed by restoration company. Upon arrival, located active leak at brass mixing valve manifold junction. Inspected copper supply lines and PEX distribution piping connected to central brass fitting with compression fittings. Repaired failed connection point where leak originated, replaced compromised compression rings and ferrules at valve assembly. Secured all pipe connections at manifold, tested system under pressure to verify repair integrity. No further leaks detected upon completion of pressure test.

Responded to service call for mini split system and installed replacement control board. During testing after board installation, identified failed electronic expansion valve (EEV) causing additional system malfunction. Replaced defective EEV to restore proper refrigerant flow control and verified complete system operation.

Completed full electrical rough-in and trim work for detached garage structure. Installed complete wiring system, circuit breaker panel with properly labeled circuit directory, and exterior gooseneck lighting fixture above entry door. Work was coordinated with scheduled rough-in inspection and all installations completed to code specifications.

Responded to electrical outlet malfunction caused by overheating from space heater usage. Upon inspection, discovered melted and burned wiring inside the receptacle. Removed damaged outlet, cut back compromised wire, and installed new duplex receptacle with proper wire terminations to restore safe electrical service.

Responded to a water heater leak at the connection point where piping meets the tank. Diagnosed a faulty temperature and pressure relief valve that was not closing properly, causing continuous water discharge through the 3/4" drain line. Removed the defective T&P valve and installed a new replacement unit, restoring the Bradford White 40-gallon natural gas water heater to proper working condition with no leaks present upon testing.

Completed annual AC tune-up and preventative maintenance on residential split system. Identified and corrected safety hazard with exposed high voltage wiring that was previously sitting in water during rain events; secured wiring to exterior wall and applied heavy-duty electrical tape reinforcement to protect connections from moisture intrusion.

Completed installation of bathroom fixtures including roman-style faucet assembly with chrome finish and white porcelain sink basin. Connected all water supply lines with shut-off valves, installed P-trap drainage assembly with corrugated drain pipe, and verified proper operation of all plumbing connections beneath vanity cabinet.

Responded to service call for Richmond tankless water heater displaying error code 14 and failing to operate properly. Upon inspection, found heat exchanger overheating during ignition attempts. Diagnosed issue as mineral buildup requiring descaling maintenance. Contacted manufacturer technical support to confirm error code 14 indicates need for heat exchanger descaling procedure. Explained findings and recommended descaling service to resolve overheating condition and restore proper operation. Customer elected to purchase descaling kit and perform maintenance independently. Documented unit condition with photos showing internal components and manufacturer identification.

Responded to service call for inadequate cooling on upper level with suspected heat pump issue. Upon inspection, reviewed system runtime data showing cooling operation at 433 hours in May versus 139 hours in April, indicating increased demand. Identified thermostat programming issue with heat and cool setpoints configured too close together, causing system cycling conflicts. Adjusted thermostat settings to proper parameters and instructed occupant on correct operation, emphasizing the importance of selecting either heating or cooling mode exclusively rather than automatic changeover to prevent equipment short cycling and ensure optimal comfort control.

Completed full replacement of residential water heater in basement utility area. Drained and disconnected existing unit, then removed and disposed of old water heater. Installed new 40-gallon Bradford White atmospheric vent water heater in same location. Made all necessary plumbing connections using copper piping, filled tank, performed system startup, and verified proper operation before departure.

Conducted on-site evaluation for customer-supplied EV charger installation. Assessed existing electrical panel located on shared wall between residence and garage. Documented panel configuration and available breaker capacity. Provided detailed installation estimate which was reviewed and approved by customer.

Completed comprehensive AC tune-up on residential outdoor condensing unit. Performed standard preventive maintenance procedures including inspection of electrical connections, refrigerant lines, condenser coil condition, and overall unit operation to ensure optimal system performance for the cooling season.

Performed comprehensive duct cleaning service with arrival at 10:00 AM. Removed accumulated dust and debris from ventilation system, thoroughly cleaned all accessible vents and ductwork components, and verified proper airflow throughout the system upon completion.

Responded to service call for non-functioning ceiling fan with operational light fixture. Upon inspection, diagnosed faulty pull-chain mechanism preventing fan motor operation while light remained unaffected. Presented repair options to customer and sold complete ceiling fan replacement. Removed existing decorative ceiling fan with brass-finished housing, five ornamental blades, and frosted globe light fixture. Installed new ceiling fan unit, ensuring proper electrical connections, secure mounting, and verified full functionality of both fan motor and lighting components upon completion.

Completed comprehensive air conditioning tune-up on outdoor condenser unit. Performed standard maintenance procedures including inspection of cylindrical fan assembly, condenser coils, electrical connections, and refrigerant levels. Unit found to be operating within normal parameters with no deficiencies identified or repairs required.