Dependable Home Services in Stewartville, MN

Responded to service call for refrigerant leak search on HVAC system. Located active leak at liquid line connection point where it meets the evaporator coil, evidenced by corrosion and oxidation on copper piping. Successfully pumped down the system, repaired the leak at the liquid line connection, and documented the corroded components with photographs for service records.

Responded to no cooling call on aging outdoor condensing unit. Upon arrival, found AC fan motor not operating. Inspection revealed burnt electrical wiring, failed condenser fan motor, and damaged condenser coils with significant debris accumulation. Unit accessibility severely compromised due to ground settling, causing equipment to be positioned directly against building structure with inadequate clearance for proper service or airflow. Heavy vegetation growth around base and extensive dirt/debris buildup on top panel indicate lack of routine maintenance. Replaced condenser fan motor and repaired burnt wiring to restore immediate operation. However, due to damaged coils and critical positioning issues from settling, unit serviceability remains compromised long-term. Recommended obtaining pricing for relocating equipment away from structure to meet manufacturer clearance specifications and allow proper maintenance access. Unit condition and age suggest consideration for replacement m

Responded to a leak under the kitchen sink caused by a corroded galvanized nipple extending from the wall connection for the left side drain assembly. Upon inspection, discovered a small hole in the bottom of the galvanized nipple due to corrosion. Removed the deteriorated nipple from the wall fitting and thoroughly cleaned the threads, which showed significant corrosion buildup. Installed a trap adapter to the existing galvanized fitting and reassembled the drain assembly. Tested the system by running the faucet and confirmed proper drainage with no leaks detected.

Responded to no cooling complaint on residential air conditioning unit. Upon arrival, diagnosed system as low on refrigerant, indicating a potential leak in the refrigerant circuit. Added refrigerant to restore proper system charge and injected UV dye pack into the system to facilitate future leak detection and pinpointing during follow-up service if needed.

Responded to callback for non-functioning Bradford White water heater. Upon inspection, assessed existing 40-gallon propane unit and determined replacement necessary. Provided estimate for new 40-gallon power vent propane water heater installation, documented existing equipment configuration including copper supply lines, gas control valve assembly, and power vent connections for replacement specifications.

Responded to service call for two leaking outdoor spigots at residential property. Upon inspection, discovered the packing nuts on both front and back exterior faucets were loose, causing water to drip when the faucets were turned on. Tightened the packing nuts on both fixtures, tested operation, and confirmed leaks were eliminated with no further issues.

Responded to callback for Richmond brand tanked water heater that had extinguished after previous service visit. Successfully relit pilot by cycling the gas control valve off and restarting the unit, setting control to B position. Pilot ignited and remained stable, with burner heating tank properly. Advised that if flame extinguishes again, gas control valve replacement will be required, and provided estimate for new water heater replacement as alternative option.

Responded to no cooling complaint on residential air conditioning system. Upon inspection, discovered burnt electrical wiring caused by severely clogged condenser coil restricting airflow and causing system overheating. Repaired damaged wiring and performed thorough condenser coil cleaning to restore proper airflow and system operation. Delivered furnace filter as requested and verified system cooling functionality upon completion.

Installed two dedicated electrical circuits in basement utility area to support dehumidifier and sump pump equipment. Ran new wiring from main electrical panel, installed appropriate circuit breakers, and labeled circuits accordingly for future reference. All work completed to code specifications and per approved estimate.

Responded to service call for AC unit leak causing water damage inside wall and drywall below attic space. Upon inspection, identified flexible ductwork accumulating condensation water due to improper drainage or insulation failure. Determined flex run requires replacement to resolve leak issue and prevent further structural damage.

Responded to service call for water softener installation after customer's unsuccessful DIY attempt resulted in leaking. Successfully installed new water softener system with complete plumbing connections, including copper supply lines, shut-off valves, and drain configuration. System tested and confirmed operational with no leaks detected upon completion.

Responded to no cooling call on 1980s-era air conditioning unit. Upon inspection, found system critically low on R-22 refrigerant and operating with diminished airflow. Unit exhibited previous startup noise issues and insufficient cooling capacity due to age and refrigerant loss. Advised that due to the system's age, obsolete R-22 refrigerant requirements, and overall condition, full system replacement is recommended over continued repairs.

Performed preventive maintenance tune-up on residential air conditioning system. Upon inspection, identified failed capacitor preventing proper compressor operation. Replaced defective capacitor with new unit rated at 35/5 MFD, 370V, restoring system to full operational capacity.

Completed site assessment for new electrical outlet installation in unfinished basement utility area. Evaluated existing electrical panel configuration and circuit capacity to determine optimal connection point for additional outlet. Assessed workspace conditions including concrete block walls, exposed ceiling joists, and available routing paths for new wiring installation.

Installed crankcase heater on residential rooftop air conditioning condenser unit. Part was successfully installed and unit is operational.

Responded to service call for furnace producing loud growling noise during startup. Upon inspection, diagnosed failing inducer motor assembly. Removed and replaced defective inducer motor with new unit to restore proper furnace operation and eliminate abnormal noise.

Responded to service call for noisy boiler and gurgling baseboard heaters. Upon inspection, determined system water level was critically low, causing air entrainment in hydronic distribution lines. Added water to boiler to restore proper system pressure and eliminate operational noise. Verified equipment returned to normal operation with quiet performance throughout baseboard heating zones.

Responded to service call for garage heater with reported water leakage. Upon inspection, identified water infiltration occurring at the exhaust vent penetration point through the roof. Observed active water dripping from the exhaust exit location and confirmed moisture accumulation on the roof surface. Extensive condensation was visible on the exhaust ductwork and surrounding components. Due to wet roof conditions preventing immediate repairs, diagnostic assessment was completed and documented with photographs. Follow-up visit will be required to address the roof penetration seal and complete necessary waterproofing repairs once conditions permit safe roof access.

Responded to no heat call on residential furnace that had been inoperative for three weeks. Upon arrival, performed diagnostic assessment and identified failed inducer motor as root cause of heating system failure. Removed access panel to access internal components, disconnected electrical connections and pressure switch tubing from failed inducer assembly. Extracted defective inducer motor from furnace cabinet and installed new replacement inducer unit. Reconnected all electrical wiring, pressure switch hoses, and exhaust piping to new motor assembly. Tested system operation to verify proper inducer function, pressure switch activation, and ignition sequence. Confirmed furnace now heating properly and restored comfort to residence.

Responded to water leak on main supply line located in basement prior to meter. Upon inspection, identified failed 3/4" ball valve as source of leak. Coordinated with municipal water department to shut off water supply at street connection. Removed defective 3/4" threaded ball valve and installed new replacement unit on main water line upstream of meter. Verified proper installation and secured all connections. Municipal water department scheduled to restore water service at street connection upon completion of work.