Trusted Home Services in Byron, MN, for Over 35 Years

Responded to gas leak at fireplace supply line traced back to main gas line connection point. Removed faulty connection fitting and installed new connection with code-compliant shut-off valve added to the gas line serving the fireplace. Performed pressure test on the repaired line to verify system integrity and confirm no additional leaks present. All work completed in accordance with applicable gas code requirements.

Responded to call for two leaking outdoor faucets on residential property. Upon inspection, identified loose packing nuts on both hose bibs as the source of water leakage. Tightened packing nuts on both exterior faucet assemblies, restoring proper seal and eliminating all leaks. Verified proper operation of both fixtures upon completion.

Responded to service call for non-functioning kitchen outlets. Upon inspection of electrical panel, discovered fuse was not properly secured and fully seated. Tightened fuse to proper specification, restoring power to affected kitchen outlets. Provided homeowner with maintenance recommendations for electrical system.

Responded to service call for water leakage issue in HVAC system. Upon arrival, discovered water accumulation on floor originating from downflow furnace with active leak at collector box. Inspected condensate drainage system including condensate pump and associated PVC piping, noting rust staining on concrete floor beneath unit indicating ongoing moisture problem. Documented furnace components, gas line connections, ductwork joints, and internal mechanical assemblies through comprehensive photographic documentation. Provided replacement estimate and coordinated with project management for furnace replacement due to extent of collector box failure.

Completed preventive maintenance tune-ups on two gas furnaces. Performed comprehensive inspections of both units, including burner operation, gas valve controls, electrical connections, and manifold assemblies. Both furnaces showed proper blue flame combustion patterns and all components were found operating within normal parameters. No deficiencies identified or repairs required on either system.

Arrived on-site and assessed existing A.O. Smith 50-gallon natural gas power vent water heater installation. Documented current equipment specifications, connections, and utility room configuration including copper supply piping, brass fittings, yellow-tagged valve assembly, and power vent motor mounted on top of unit. Prepared comprehensive estimate for replacement of 50-gallon natural gas power vent water heater with comparable equipment and necessary connections.

Responded to callback for recurring air error message on Bradford White heat pump water heater. Upon inspection, diagnosed potential mechanical seizure of the electronic expansion valve (EEV). Contacted manufacturer technical support to verify troubleshooting steps and discuss warranty coverage for required components. Based on technical support consultation, determined control board replacement necessary to resolve recurring fault code. Documented equipment condition with photographs showing unit installation, plumbing connections, and control panel display. Coordinated with manufacturer for warranty parts procurement prior to scheduling follow-up repair visit.

Responded to service call for leak under kitchen sink. Upon arrival, identified source of leak at existing kitchen faucet. Removed old kitchen faucet assembly from countertop mounting. Installed new customer-provided kitchen faucet with tall spout and side spray attachment onto granite composite countertop. Connected flexible braided stainless steel supply lines to hot and cold water supply valves. Secured supply lines with proper fasteners and verified all connections were tight and leak-free. Tested new faucet installation for proper operation and confirmed no leaks present under sink or at mounting points. Left work area clean with fully functional faucet assembly.

Responded to 6-1 error code on 50-gallon A.O. Smith ProLine XE power vent water heater. Diagnosed failed hot surface igniter preventing proper ignition sequence. Removed defective igniter assembly and installed manufacturer-approved replacement part. Tested gas control valve operation, verified proper venting through PVC exhaust system, and confirmed all electrical connections secure. Cycled unit through multiple heating cycles to ensure reliable ignition and proper burner operation. Water heater restored to full functionality with no error codes present upon completion.

Responded to no heat call where pilot light would not remain lit. Diagnosed faulty pressure switch preventing proper system operation. Replaced defective pressure switch and restored heating system to normal operation.

Responded to repeat service call for Bradford White heat pump water heater displaying FF error code related to air system malfunction. Upon inspection, diagnosed seized electronic expansion valve (EEV) preventing proper refrigerant flow through the heat pump system. Documented unit condition and component failure with photographs of internal compartment showing copper refrigerant lines, blower assembly, and electrical connections, as well as external view of unit with control panel and plumbing connections. Determined unit requires warranty replacement due to failed EEV component that cannot be freed or repaired in field conditions.

Responded to no cooling complaint and performed diagnostic evaluation of outdoor condensing unit. Found system operating with low refrigerant charge, indicating leak in refrigerant circuit. Due to advanced age of equipment and extent of required repairs including leak detection, refrigerant recovery, repair, and recharge, recommended full system replacement as most cost-effective solution.

Responded to no-cooling call for attic-mounted air conditioning unit. Customer was not present upon arrival despite multiple attempts to make contact. Left door hanger with service information and contact details for customer to reschedule or discuss temporary repair options, as unit is scheduled for replacement with new installation.

Completed routine preventive maintenance on residential air conditioning system. Performed comprehensive tune-up including electrical measurements with amperage readings at 498, verified system operating temperatures, and inspected outdoor condenser unit. All components found operating within normal parameters.

Completed installation estimate for GFCI outlet in bathroom and provided assessment for gas line bonding requirements at meter. Documented existing electrical panel configuration and newly installed standard duplex receptacle with proper grounding.

Responded to no-cool call on residential HVAC system where outdoor unit fan was not operating. Diagnosed failed dual run capacitor preventing condenser fan motor operation. Replaced defective capacitor with new unit, restored system to proper operation, and verified cooling cycle functionality.

Completed comprehensive seasonal maintenance on residential furnace and outdoor heat pump/AC condenser unit. Performed standard tune-up procedures including system inspection, cleaning, and operational testing to ensure optimal performance and efficiency for both heating and cooling systems.

Responded to service call for toilet reported to be constantly running with leaking underneath. Upon inspection, identified leak originating from loose water supply line connection at toilet fill valve. Tightened supply line connection to resolve leak. Inspected additional toilets throughout residence as requested. All plumbing connections secured and functioning properly upon completion.

Responded to service call for leaking faucet and improperly draining floor drains in garage. Upon inspection, identified back-pitched floor drains causing drainage issues and a dripping hot/cold faucet at hose connection. Determined that faucet replacement would require creating interior wall access for proper connection. Per customer request, capped the hose connection instead of full faucet replacement to avoid interior wall modification.

Responded to service call for air conditioning unit requiring releveling. Upon arrival, assessed the outdoor condensing unit and determined it had settled unevenly on its concrete pad. Successfully leveled the AC unit to manufacturer specifications to ensure proper operation, drainage, and equipment longevity.