Protecting Your Investment with Expert Home Services in Zumbrota, MN

Responded to no-heat call and diagnosed failed hot surface igniter preventing furnace operation. Replaced defective hot surface igniter with temporary unit to restore heating function. Follow-up visit required to install OEM hot surface igniter for permanent repair.

Responded to emergency service call for residential property without power. Conducted site assessment of existing fuse box located in bathroom that required relocation to opposite side of wall in garage landing area. Inspected current electrical service entrance, meter installation, and conduit routing on exterior wall. Evaluated interior wall configuration and existing electrical infrastructure to determine feasibility of panel relocation. Provided detailed estimate for complete panel replacement and relocation project, including removal of outdated fuse box, installation of modern circuit breaker panel in new location, and necessary electrical connections to restore power safely and bring system up to current code requirements.

Completed FRM electrical inspection of residential property. Verified all GFCI outlets are properly installed in required locations throughout the home, including laundry area and utility spaces. All electrical systems, wiring, and protective devices meet current code requirements with no deficiencies identified or corrective work needed.

Responded to service call for furnace with water leakage on floor. Upon inspection, identified two sources of water intrusion: a leaking humidifier hose and condensate backup into the furnace cabinet. Cleared blockage from condensate drain line to restore proper drainage flow and replaced the damaged drain line section. Repaired humidifier connection to eliminate leak at that point. Verified system operation and confirmed no further water accumulation.

# Sump Pump Inspection and Assessment Responded to customer concern regarding sump pump capacity ahead of anticipated snow melt season. Upon arrival, performed comprehensive inspection of existing sump pump system and basin. Verified pump operation through functional testing, confirming unit is currently cycling and discharging properly. Inspected sump basin and found adequate water level management with visible pump components including discharge piping, check valve assembly, and pump housing in working condition. Noted the unit is an older model showing age-related wear, with visible mineral deposits and moisture accumulation consistent with normal operation in this environment. Informed customer that while the current pump is functioning as designed, the age of the unit warrants consideration for replacement to ensure reliability during high-volume water events. Provided estimate for new sump pump installation as a proactive measure to prevent potential failure during peak deman

Arrived on site and assessed damaged exterior water spigot. Removed old burst faucet and installed new copper pipe assembly with frost-free outdoor spigot as per estimate. Restored water service to residence and verified proper operation with no leaks.

Responded to inspection correction callback. Installed a new GFCI/AFCI combo outlet in the basement to provide proper arc fault and ground fault protection as required by code. Verified proper functionality of the new device after installation.

Responded to emergency service call for water intrusion in basement. Diagnosed burst outdoor spigot that activated during vehicle washing. Inspected damage to ceiling and documented with photos. Provided customer with estimate for replacement spigot installation.

Replaced condensate drain line on Goodman furnace system. Temporarily operated condensate pump during service. Provided customer with quotation for new furnace replacement. Issues with the original drainage system were resolved by installing proper PVC adapter and permanent drain line configuration.

Responded to service call for a burst pipe in basement. Upon inspection, identified leak occurring prior to water meter with significant corrosion and deterioration of copper piping. Customer was advised to contact Zumbrota water department to install new valve prior to meter as the issue was beyond serviceable area.

Responded to emergency call for burst pipe in customer's basement. Upon inspection, identified leak at plumbing connection against concrete wall with significant water damage and debris buildup around the fitting. Customer had water shut off by city prior to arrival. Service appointment was rescheduled as customer was informed of technician's delayed arrival.

Responded to no heat complaint caused by frozen condensate drain line due to oversized fresh air return. Plugged the fresh air return and installed a temporary condensate line with pump to restore system operation.

Conducted annual tune-up service on Carrier furnace system. Performed combustion analysis with readings showing normal CO levels (23F), CO₂ at 39P, 7.0% CO2, and 4.6% excess air. All components inspected and functioning properly with no issues identified.

Responded to service callback for previously replaced inducer motor with continued no-heat condition. Upon arrival, discovered gas shutoff valve and gas valve were in off position. Restored gas supply, verified proper operation of heat exchanger, and confirmed system function.

Responded to service call for a leaking pipe in the mechanical room. Discovered a hole in a 1 1/2" galvanized kitchen drain line showing significant corrosion at the connection point. Applied temporary patch to control the leak; will return with a 1 1/2" Fernco coupling to properly repair the damaged section.

Diagnosed complete furnace failure due to cracked heat exchanger in commercial basement utility room. System deemed unsafe to operate. Connected customer with project manager to discuss necessary replacement options.

Performed annual preventive maintenance tune-up on gas furnace. Inspected internal components and connections while unit was opened. Checked PVC venting system and propane gas line for proper installation. All systems functioning normally; no issues identified.

Performed comprehensive duct cleaning service on HVAC system, addressing accumulated dust and debris throughout ductwork. Inspection revealed significant dust buildup in metal ducts, particularly around connection points and vents. Successfully cleaned all vents and ductwork to restore proper airflow and system efficiency.

Responded to no heat service call. Diagnosed failed pressure switch preventing furnace operation. Replaced defective pressure switch, restoring normal heating function.

Performed comprehensive duct cleaning consultation in customer's unfinished basement, examining HVAC system with open furnace panel for inspection. Assessed existing ductwork configuration running through exposed ceiling joists, documenting current system condition with photographic evidence for service recommendation.