Reliable Heating, Air Conditioning, Plumbing, and Electrical Services in Winona, MN

Responded to building-wide low water pressure complaint. Investigated plumbing system and identified clogged cartridges in the main brass valve manifold assembly as the source of reduced flow throughout the facility. Removed and replaced affected cartridges, restoring proper water pressure to all fixtures. Verified system operation at kitchen sink and confirmed adequate pressure restoration.

Installed American Standard shower valve cartridge to address shower/tub temperature control issue. Upon testing, the cartridge replacement did not resolve the problem, indicating a potential issue with the hot water supply line feeding the bathroom. Recommended further investigation of the hot water supply line and follow-up consultation to determine next steps for complete repair.

Installed new electrical outlet with cover plate inside cabinet above range to accommodate wall-mounted microwave. Previous microwave was hard-wired; converted to plug-in configuration by adding dedicated receptacle within cabinet compartment. Outlet positioned for proper microwave connection and secured according to electrical code requirements.

Responded to gas leak call at residential property. Upon arrival, identified gas leak at cracked brass fitting where gas pipe connected to supply line. Leak was determined to be caused by defective fitting from original installation. Shut off gas supply and replaced compromised gas line section and brass fitting with new components. Performed pressure test to verify integrity of repair and confirm no additional leaks present. Completed preventive maintenance assessment (PMA) on air handler unit, including inspection of all mechanical components, electrical connections, and operational systems. Performed standard tune-up procedures on air handler to ensure optimal performance and efficiency. All systems tested and returned to normal operation with no gas leaks detected.

Responded to service call for water softener not dispensing salt despite operational dials. Diagnosed salt bridge formation in brine tank preventing proper regeneration cycle. Broke up salt bridge, initiated manual regeneration cycle, and verified system returned to normal operation with proper salt dispensing and softening functionality.

Responded to service call for leaking outdoor hose bib. Upon inspection, identified failed stem assembly as source of leak. Successfully replaced stem assembly in exterior wall-mounted spigot, restoring proper function and eliminating water loss. Verified repair with pressure test to ensure complete seal and proper operation.

Responded to no cooling complaint on residential air conditioning system. Upon inspection, diagnosed failed capacitor preventing compressor operation. Replaced defective capacitor and restored system to normal cooling operation.

Responded to service call for leaking water heater. Upon arrival, confirmed active leak from tanked water heater requiring immediate replacement. Removed existing failed unit and installed new tanked water heater. Connected all necessary water supply lines, pressure relief valve, and drain pan. Verified proper venting, tested all connections for leaks, and confirmed unit operational. Also observed water filtration system with dual canister filters installed under sink during inspection of plumbing connections.

Responded to no cooling complaint on unit less than 10 years old and discovered incomplete installation from previous work. Released refrigerant from system, vacuumed lines to remove contaminants and moisture, and performed fresh solder connections on refrigerant lines at outdoor condenser unit where brass fittings and copper piping required proper joining. Completed the installation to manufacturer specifications, ensuring all refrigerant line connections were secure and properly sealed at the service valve assembly.

Completed installation of a 40-gallon power vent water heater and a one-piece Water Right Impressions water softener system in the basement utility area. Established all necessary plumbing connections, configured the power vent exhaust system, and mounted the digital control panel for system operation.

Responded to no cooling complaint on residential air conditioning system. Upon arrival, found thermostat improperly wired, preventing system operation and indoor fan from running. Corrected thermostat wiring connections at terminal block, restoring proper communication between thermostat and outdoor condensing unit. Verified system operation and confirmed cooling function restored.

Responded to emergency call for active water leak at mobile home. Upon arrival, found electric water heater with continuous leak causing water accumulation on floor. Customer had already shut off water supply valve, but leak persisted until proper isolation valve was closed. Assessed water heater condition in confined crawl space area with limited access. Unit showed signs of failure requiring full replacement. Shut off power at electrical breaker panel and completed water supply isolation. Removed failed electric water heater unit from mechanical space. Installed replacement electric water heater with new connections to existing electrical service and plumbing lines. Verified all connections for proper seal and tested system operation. Restored power and water supply, confirmed no leaks present, and ensured proper hot water delivery throughout residence.

Arrived on-site to assess existing water treatment system consisting of an in-place iron filter and water softener. Conducted thorough evaluation of current equipment including a tall black filtration tank with digital control head, blue Well X1000 pressure tank, and existing water softener with associated copper piping and connections. Documented system configuration showing multiple cylindrical tanks with control units, copper supply lines with various fittings and elbows, and electrical wiring connections. Observed moisture staining on concrete floor near equipment base indicating potential system inefficiency. Photographed complete installation including pipe routing, tank positioning, insulated sections, valve components, and spray foam insulation on foundation walls. Prepared comprehensive estimate for replacement iron filter and water softener system to address water quality concerns and improve filtration performance.

Responded to no cooling complaint on Guardian brand air conditioning system. Upon diagnostic evaluation, determined system was low on refrigerant charge. Advised customer of options to either locate and repair refrigerant leak or consider system replacement.

Responded to no cooling complaint on Tempstar outdoor condensing unit. Upon arrival, found AC fan motor spline stuck due to rust accumulation, preventing proper fan operation. Lubricated spline with appropriate oil and cycled system to verify free rotation of fan motor. Tested unit operation and confirmed system cooling properly with fan running at normal speed.

Responded to service call for water heater and water softener evaluation. Upon arrival, assessed existing 40-gallon atmospheric water heater and single-piece water softener system in basement utility area. Documented current equipment condition and configuration, including existing plumbing connections and spatial constraints. Provided comprehensive estimate for complete replacement of both the water heater and water softener unit. Photographed existing installation for reference and documentation purposes.

Performed preventative maintenance on A.O. Smith FVIR-compliant tanked water heater located in lower level utility room. Completed full tank flush to remove sediment buildup and replaced deteriorated anode rod to extend tank life and prevent corrosion. Replaced Suel laundry tub in lower level and provided estimate for additional water heater service recommendations.

Responded to service call for geothermal system emitting odor during operation. Upon inspection, identified source as 30-year-old fan coil unit with severely deteriorated electrical wiring showing burn marks and exposed conductors, along with heavily corroded drain pan causing water leakage into return air plenum. Due to safety hazards and extent of deterioration, de-energized fan coil unit at breaker and documented conditions with photographs. Coordinated with project management team to schedule equipment replacement estimate.

Replaced defective refrigerator water supply line with new line to restore proper water flow to the appliance. Installation completed in unfinished interior space with exposed wiring and construction materials present.

Conducted on-site assessment for hot tub electrical installation in basement utility area. Evaluated existing electrical panel capacity and circuit breaker configuration to determine feasibility of extending dedicated circuit to future hot tub location. Inspected current electrical infrastructure, including panel load capacity, available breaker slots, and wire routing pathways through exposed framing. Provided detailed estimate for installation of new outlet at designated hot tub location, pending delivery and final placement of unit.